When there is a need to keep the legs apart. Can give satbility and better posture. Fabric black Skai.

Armrest plate designed for users who are hemiplegics. Fabric black Skai.

This armrest plate is mounted as standard on our classic 200 work chair with soft plush

This armrest plate is mounted as standard on our classic 200 work chair.

This armrest plate is mounted as standard on our classic 200 work chair.

Arm support rods for the height adjustment. Available in a numbre of types. Delivered without arm support plate.

Arm support foldable backwards. Makes side transfers easier for the user when getting in and out of the chair.

The sling back can be shaped after theusers back with 5 adjustable straps under the upholster. Recommended for users with kyphosis.

Seat belt for the hip. In black Skai.

To be mounted in the combi hold when using divided leg supports, amp. support or adapters for other manufacturers leg supports. One on each side.

For users who are amputaded and extra support. To be used together with the combi hold.

Divided leg support electrically adjustable in angle. Only for work chairs with electric seat lift. Adjustable in angle by the knee and ankle with length compensation. Operated with a control box. Delivered with calf support.

The head restraint designed to support head and neck. It also supports the skull behind the ears to prevent the head from falling to one side. Adjustable in height, depth and angle.

A hold when mounting a head support on a sling back

Is needed when you want to use leg supports from other manufacturers on our products. Available for most of the bigger brands. Tobe used together with the combi hold and width adjustment hold.

Recommended when you want to use a separate seat cushions to superimpose the plane seat. Ordered by dimensions!

Protects the upholster from worn and incontinence.

Transparent tray/table in i plexi. Complete with hold.

BUS station för inkoppling av flera Dynamic tillbehör.

Alternative joystick knobs.
These alternative knobs can be mounted on all Dynamic control boxes to adapt them to the user.
For people with trouble holding the standard grip, one of these altaernatives may be an opportunity to get a better grip and thus better control over the wheelchair.

Carer control of seat functions. Is connected into the Dynamic electronic and replacecs the menu functions of the G90T.
Note ! The electronics needs to be reprogrammed with the Wizard ! Enable "ARC enable" !

Control box G90A have two 3.5 mm teleplugs instead of the toggle switches that is standard on G90T. It also has hot keys for flashers. Controls up to 5 seat functions on the joystick. Clear symbols showing which seat function selected. Programmed with the new Wizard 5 hand programmer.

Standard control box for DX Compact. Controls up to 5 seat functions. Obvious symbols explains what seat function is activated. Is programmed with the new Wizard 5 or the hand programmer.

The new standard control box on our indoor power wheel chairs Miniflex and Flexmobil. Controls up to two seat functions. Is programmed with Wizard 5

Combined actuator and light module. Is used to control the seat functions and lights (if mounted)

(Combined Light and Actuator Module, CLAM)

Links the power from the batteries out to the motors For control box G90.

24 Volt 2x70 amp
185x125x45mm
1,4 kg

Links the power from the batteries out to the motors. For control box shark.

Wizard programming kit for PC. It’s a tool for programming the electronics of our power wheel chairs. The soft ware is free to down load from here below, but you also need a hard ware lock (dongle) and cable to connect to the wheel chair to.
Contains: soft ware Wizard 5
programming cable (USB)
hard ware lock (dongle) (USB)

Controls the wheel chair with a finger that is put in the hole. Proportional!

Used together with control box SCR and then you can get full environmental control. Anything that is controlled by IR you can program into the IRIS. You build up menus in the SCR that is connected to the programmed functions in the IRIS. You need the Wizard 3.1b to program the SCR and the hand controller to program the IRIS.

To be used together with IRIS. Makes it possible to control your PC with the joystick from the wheel chair. Connected to a free serial port on your PC ( not MAC)

A very small and light touch proportional joystick. With a stroke of +/- 10 mm and a force of 6g it is very suitable for weak users.

Separate joystick that can work together with the standard control box. Could be a solution for users who needs to alternate between left and right hand.

When you want to control the wheel chair with sif and puff with your mouth.
Is programmed with Wizard 3.1b